Then open the CD image and create a Windows 95 'FDD' folder in the root file. In this file, add the folders we just created by unzipping the CAB files in the FDD case. Then save the changes. Now to the boot disk. To do this, go to the website 'bootdisk.com' and download the disk 'Windows 95 Original'. Or download the floppy in flp format.

Impact soundworks impact steel. The goal of Groove Bias was to create a set of deeply sampled acoustic drum kits inspired by classic 50s, 60s and 70s records and the timeless breakbeats we all know and love. For decades, these sounds have been imitated and sampled over and over, but many producers have preferred to try and capture old kits with pristine, modern recording methods.

If you are experiencing issues with the floppy drive in your computer, review the troubleshooting options below to try and resolve the problem.

The troubleshooting options and details below are for floppy disk drive issues and not for issues about not being able to read one or two floppy disks.

Bad floppy diskette

Verify the floppy diskette you are attempting to read from is not write protected or bad. Verify the diskette is not write protected by sliding the tab into the opposite position, preventing light from shining through it. If you do not have a tab, place tape over this hole.

Because of the technology of floppy diskette drives, the floppy diskettes ist most likely bad. Verify that other floppy diskettes are not exhibiting the same issue.

If other floppies work, you may have a bad floppy diskette.

Not setup in CMOS

Verify the floppy drive is properly set up in CMOS setup. If the floppy drive is not set up properly, you may experience read/write errors or the floppy may not work at all. Most computers need to have the floppy setup as a 3.5, 1.44 MB.

Eliminating possible conflicts with other hardware

If you have recently installed any new hardware, you should consider disconnecting it temporarily to ensure that it is not the cause of your floppy drive not working.

Not connected properly

• Power down, unplug, and open the computer, being aware of ESD and its potential dangers.
• Verify the floppy connection is connected to the motherboard FDD connector. If it appears to be connected, disconnect and then reconnect the cable to verify the cable is seated properly.
• Verify the floppy cable coming from the motherboard is connected to the back of the floppy drive. If connected, disconnect and reconnect the floppy drive cable to verify it is seated properly.

• Verify a power cable is connected to the back of the floppy drive.
• If your floppy cable has more than one connection, verify that you have connected the floppy to the appropriate connection. The above picture illustrates what drive should be connected where.

Bad drivers

If you are not able to read or write to a floppy diskette from Windows, verify the computer is not exhibiting floppy driver issues by testing the floppy drive from MS-DOS.

If you are running Windows 95, Windows 98, Windows ME, Windows NT, Windows 2000, or Windows 2000, click Start, Shutdown, and Restart the computer to an MS-DOS prompt.

If you are running Windows 3.x, click File and select Exit Windows to get to an MS-DOS prompt.

Once at the prompt, place a diskette into the floppy disk drive and type format a:.

If you receive any of the following errors when trying to format the floppy disk:

Invalid media or Track 0 Bad - Try formatting another floppy disk.
Write Protect Error - Ensure the disk is not write protected by removing the floppy disk and verifying you cannot see through both holes. If you can see light, move the tab on the left side (looking from the back of the floppy) to the down position and try again. If the disk is not write protected, try another floppy disk.
Invalid drive specification - Verify the floppy drive is set up properly in CMOS setup.

If the floppy disk drive formats properly in MS-DOS but does not format in Windows, Windows or a program within Windows is preventing the floppy drive from working. End task all running TSRs and background programs. If you continue to experience the same issues, we recommend that Windows be reinstalled.

Bad hardware

If you continue to experience issues after following the above steps, hardware in the computer is bad. Replace the following hardware in the computer in the below order.

1. Replace the floppy data cable that connects the computer floppy drive to the motherboard.
2. Replace the floppy drive if the floppy data cable did not resolve your issues.
3. Replace or request that the motherboard be replaced.

Additional information

• See our floppy disk and floppy drive definitions for further information on each of these terms.